Nowadays, improving the working efficiency is a special concern of the Injection Molding Machine industry. Due to the long working time of the injection molding machine, the damage to the internal machinery and equipment of the injection molding machine is very serious, which reduces the service life of the machine, which not only increases the service li...

(1). Wire connector inspection Wires that are not fastened by the joint may cause high temperature or sparking damage at the joint position. Poor joints may also affect the transmission of the signal; the joint on the contactor may be loosened due to the vibration of the electromagnetic action, so the timing check connector is required. Position and...

At present, many mechanical manufacturers are choosing the Plastic Injection Molding Machine manipulator as the main mode of production, but the use of automated manipulator in production can improve the production efficiency and product quality and reduce the production cost of products have greatly improved, in the production of Injection Moulding Machi...

The barrel and screw form the extrusion system of the Injection Moulding Machine. Like the screw, the barrel is also operated under high pressure, high temperature, severe wear and certain corrosive conditions. During the extrusion process, the barrel also has the effect of transferring heat to the material or transferring heat away from the material. A h...

First, the cause of the dent 1, the thickness of each part of the product is different 2, the mold is under pressure 3, mold cooling is not enough 4. Deformation due to insufficient cooling time Second, the associated knowledge 1. In the process of producing products, the dent is the most frequent occurrence of the bad ...

Which brand of General Purpose Plastic Injection Molding Machine is good? As a plastic molding equipment, injection molding machine plays an increasingly important role in many different applications with a variety of different types of equipment. It is necessary to mold a lot of plastic paper in everyday life. Attentions for Plastic Injection Moldi...

In the plastic processing industry of our society, the injection molding machine is one of the most widely used processing machinery. A large number of our daily necessities are produced directly by the injection molding machine. This allows us in the process of injection molding machine, there are many enterprises will appear injection molding machine ha...

(1) Injection system The effect of the injection system: the injection system is one of the most important components of the Injection Molding Machine. There are generally three main methods of plunger type, screw type and screw pre-plastic plunger type. The most widely used now is the screw type. The effect is that, in a cycle of the injection molding ma...

Most of the plastic products in daily life are produced by Energy Saving Plastic Injection Machine. The injection molding of plastic products requires the use of molds, which means that the complete injection molding solution should be the injection molding machine + mold. This has some requirements for the injection molding machine and the matching mold....

The operation of the Full Automatic PET Bottle Blow Molding Machine - as the name suggests is the running process. The PET automatic blow molding machine is a two-way stretching process during the blowing process. During this process, the PET chain is bidirectionally extended, oriented and aligned, thereby increasing the mechanical properties of the bottle ...

This article is provided by China Plastic Blow Molding Machine Factory 1. The injection equipment and the clamping equipment are on the same straight base line, and the mold is opened and closed along the upper and lower sides, covering half of the floor area of the horizontal machine. 2. Simple completion of the mosaic molding, mold upward, insert into th...

Conceptual comparison Plastic Extrusion Blow Molding Machine: Extrusion is also known as extrusion in plastic processing, and is used in the processing of non-rubber extruders by using hydraulic press pressure to extrude the extrusion of the mold itself. It refers to a processing method in which the material passes through the action between t...

Most of the plastic products in daily life are produced by injection molding machine. The injection molding of plastic products requires the use of molds, which means that the complete injection molding solution should be the injection molding machine + mold. This has some requirements for the Plastic Injection Machine and the matching mold. Today, Plasti...

1. Servo Energy Saving Plastic Injection Machine in use of the mold: mainly used in the middle mold option setting whether the injection molding machine has adopted the middle mold, if the medium mode above the setting, then Plastic Bottle Making Machine Supplier's manipulator must wait until the completion of the injection molding machine, the mold wil...

Nitrogen bottle for High Speed Injection Molding Machine Nitrogen bottles are also called accumulators. It is inside the rubber bladder of the high pressure nitrogen bottle because the pressurized oil is filled with high pressure on the remaining space. Therefore, at the time of injection, the pressure oil will be released, which is a basic constan...

In the past, the rapid development of plastic bottle packaging, the domestic blow molding machine industry is also rapidly emerging. The manufacturing and R&D technology of the blow molding machine is constantly shrinking with the international advanced level. It should be said that the rapid development of the blow molding machine enterprises cannot ...

What is the relationship between the blow molding machine and the High Speed Injection Molding Machine? Plastic Bottle Making Machine Factory tell you. Blowing machine: It is the machine that blows the bottle. The most obvious explanation is the machine that can blow plastic pellets or finished preforms into bottles by certain means. At present, most o...

Hollow Plastic Molding Machine Supplier produce surface engineering technology as a system engineering that changes the morphology, chemical composition and structure of solid metal or non-metal surfaces to achieve the desired surface properties. There are three main categories: First, the mold surface modification technology uses plasma, laser, electron b...

The energy saving of an injection molding machine can be divided into two parts: one is the power part and the other is the heating part. Throughout the various forms of injection molding machine energy-saving transformation on the market, Servo Energy Saving Plastic Injection Machine with its high stability and high energy-saving rate is now the most rel...

Plastic Bottle Making Machine Suppliers tells you that if the bottle and mold are not matched or the bottle can be discerned, the pressure of the Plastic Bottle Making Machine is checked. (General pressure is about 2.0-3.0MPA), if the pressure is normal. Then check whether the exhaust structure of the mold is open, and check that the temperature is normal...